22

2020-07

Knowledge Popularization on Upper Corner of Return Air in Fully Mechanized Coal Mining Face

What is the upper corner of return air in coal mining face? The corner (yu, second tone) means the corner, and the corner refers to the corner position. The upper corner is generally a mining noun, which refers to the return air side of the coal mining face and the triangular zone near the upper side of the return air lane and the edge of the goaf. The ventilation in this area is not good, the temperature and humidity are high, and it is easy to accumulate the gas released by the intersection of goaf and mining face, and the gas concentration is high. It is the focus of gas prevention and control in working face.

2020-07-22

22

2020-07

Warm Tips of Yikuang Science and Technology -60 Things to Do during the Great Summer Heat

When the summer heat arrives, the summer is thick! Today is the heat, It means the roast day of the year is coming ~ The season of love and hate, 60 things we can do, Each piece is summer limited, One less is not perfect!

2020-07-22

22

2020-07

Introduction of ZDY1200L crawler type full hydraulic drilling rig in underground coal mine

ZDY1200L crawler type full hydraulic drilling rig belongs to self-propelled, low speed, small torque type drilling rig. Equipped with electromagnetic starter, through the carbody turntable can adjust the drill hole direction. It is suitable for coal mine underground using spiral drill pipe and outer flat drill pipe to construct gas drainage drilling and water exploration and drainage drilling. Drilling depth: 100/200M matching drill pipe diameter: 78, 88 (spiral drill pipe),50/42 (outer flat drill pipe) maximum torque: 1200 rotation speed: 80~280 maximum feed overpull force: 45 feed stroke: 1000 spindle inclination angle: can be modified to -10~60 azimuth adjustment: 13

2020-07-22

22

2020-07

Introduction to Underground Tunnel Drilling

There are many kinds of underground mineral resources in China, and the geomorphic geological structure of many metal deposits and rare metal deposits are relatively complex in terms of ore body morphology and grade changes. In order to obtain reserves above grade C, it is necessary to use a combination of surface drilling and underground tunnel drilling to reach them. Underground tunnel drilling refers to the drilling work of drilling holes at different angles in narrow underground tunnels with special drilling rigs. Compared with surface drilling, tunnel drilling is mostly a full range of small-diameter shallow holes. We know that surface drilling due to the topography of the ore body morphology and other conditions, often through a very thick cover layer to control the ore body. While using tunnel excavation to control the ore body

2020-07-22

22

2020-07

Do you know the matters needing attention of rotary digging machine drill pipe

Precautions for Use of Drill Pipe of Rotary Digger? Drill pipe and drill bit can only be used for drilling pile hole, and are not allowed to be used for soil transfer, handling or leveling of construction site. Never immerse the drill in liquid concrete. The drilling operation can only be started when the drill bit touches the bottom of the hole. When drilling into sand layer or pebble layer, the driver should pay special attention to it. When drilling, the footage should not be too deep at one time. Otherwise, the hole wall will shrink, so that there will be no gap between the barrel wall of the drill bit and the hole wall, which will cause the drill bit to fail to reverse or lift, causing major accidents such as sticking. According to the geological environment, to select the appropriate drilling bucket. Selection of suitable and geological requirements of the drilling bucket, both to improve the work

2020-07-22

22

2020-07

Rotary Excavator Drill Pipe Configuration Scheme

Drilling rod configuration skills of rotary digging machine: 1. During the construction of rotary digging machine, the drilling rod shall be locked by the machine for drilling hard strata and the drilling rod for drilling soft strata shall be strictly observed. 2. When the user determines that a certain formation needs to be drilled for a long time, it is recommended to configure two sets of the same drill pipe for alternate use, so that the drill pipe can be maintained and repaired in time to ensure the user's construction progress. 3. Due to the special geology, it is necessary to use drill pipe to resist torsion. When the compressive capacity is less than the output of the drilling machine, appropriate measures must be taken to protect the drill pipe of the rotary digging machine from damage. 4. When using the drill pipe of the rotary excavator, the user must first understand the instructions to avoid wrong operation.

2020-07-22

22

2020-07

Daily Maintenance Skills of Drill Pipe of Rotary Digging Machine

Daily maintenance skills of drill pipe of rotary digging machine: 1. First, the drill pipe lifter should be maintained and butter should be added; When filling the grease nozzle at one end of the lifter, the grease nozzle at the other end must be unscrewed. This helps to squeeze out the previously noted butter, which may be mixed with water or other impurities. On the other hand, the oil seal in the lifter may be squeezed out, and dirty water containing fine sand and mud can easily enter, which will rub the bearing to reduce the sensitivity of the lifter. 2. Before each shift, butter should be added to the bearing of the drill pipe traveling device; 3. Check whether the wire rope of the drill pipe of the rotary excavator is complete. 4, often check the oil pipe, sealing ring damage, prepare

2020-07-22

22

2020-07

How to grind the standard drill bit to make it easier to use?

A standard drill bit is a very common drilling tool. It has a simple structure and convenient sharpening, but it is not the same easy thing to really sharpen it well and master the methods and skills of sharpening. Whether the drill is easy to use or not mainly depends on the hardness of the material of the drill bit and the texture of the corresponding drilled object, that is, only when you have a diamond can you dare to do porcelain work. Of course, the sharpness of the drill blade is also very important. How to grind a CNC drill well? It depends on what you have. It is best to have an electric grinding wheel or something like that: 1. You need to observe the angle of the edge of the new drill. Artificial repair wear drill only needs to grind to that angle.

2020-07-22

22

2020-07

Geological Drill Pipe Technology Characteristics of Geological Drill Pipe for Coal Mine

The geological drill pipe for coal mine is a geological exploration tool made of geological alloy steel pipe through friction welding process. The main body of the geological drill pipe is made of geological special alloy steel pipe (42MnMo7), and the drill bit of the geological drill pipe is made of high-quality alloy structural steel (42CrMo) through vacuum thermal conditioning treatment, which greatly improves the fatigue strength and shear strength. The production process of 1. products adopts imported friction machine welding and the production process is very selective. The drill pipe has the characteristics of high bending strength, firm welding and no falling off. It can ensure the requirements of straightness when drilling deep holes, and the geological drill pipe used in coal mines has high fatigue resistance.

2020-07-22

22

2020-07

What is a tunnel drilling rig? What are the commonly used tunnel drilling rig models?

Tunnel drilling rig refers to the drilling rig used to drill in the underground roadway of the mine Secondary specialized school the geological survey drilling project. Tunnel drilling rig is mainly used for deep geological exploration, gas drainage, injection and drainage, ventilation, etc. The tunnel drilling rig has the characteristics of good disintegration, light weight of each component, and the drilling direction can be 0 ° ~ 360 °. The range is conveniently adjusted. According to the use of power, it can be divided into vertical shaft type (including spiral differential feed) and power head type (mechanical and full hydraulic). The driving mode can be pneumatic, hydraulic and electric. The main components of the drilling rig are power machine (group), gyrator, drilling tool pulling mechanism, drilling tool.

2020-07-22

< 1...656667...129 >

Copyright©2024 Shandong Yikuang Drilling Technology Co., Ltd.

Business License

Powered by:300.cn | SEO Tags