23

2021-03

Causes of drill pipe breakage-geological drill pipe manufacturers-diamond drill bit manufacturers-composite chip drill bit manufacturers

There are probably the following reasons for the broken drill pipe: 1. Material and processing (1) Drill pipe material. Nowadays, the market for drilling materials is relatively chaotic, and dishonest merchants are shoddy. The vast majority of users only consider low prices, but do not have the ability to distinguish the quality of pipes and purchase them indiscriminately. Many users spent high prices, bought sub-material pipes, and said plausibly how good their things are. (2) Processing quality. The quality mainly depends on the processing standard, processing type, processing quality, processing accuracy and so on. Mainly depends on the equipment, mainly divided into ordinary lathe processing (does not guarantee the thread size does not guarantee the straightness), single head

2021-03-23

23

2021-03

What are the wrong operation methods of triangular drill pipe? -- Yikuang Technology

Three wrong operation methods of drill rod: 1. When pressed, no pressure point can be found, and a mechanical locking rod is used as a friction rod. The contact surface between the inner rod and the two rods is very small. In a short time, the upper end of the rod and the sides of the two rods are severely worn, creating a lever or scroll button. 2. During operation, the front track of the main engine is raised, using the rear of the mast, a part of the mast is subjected to the backward force F1 of the power head and the inner part of each pole. The vertical force F2 is maintained, and both forces form a moment to a portion of the rod. The top assembly of the top and bottom of a part of the rod is easy to cut off. 3. In the process of placing the drill pipe

2021-03-23

23

2021-03

YIKUANG TECHNOLOGY Drill bit Drill pipe connecting sleeve

YIKUANG TECHNOLOGY Drill bit Drill pipe connecting sleeve

2021-03-23

23

2021-03

How to apply directional drill bit-beneficial mining technology

Directional drilling is a drilling method that uses the natural bending law of the borehole or the use of artificial oblique tools to extend the directional borehole to the intended target according to the design requirements. It can also be explained by the technology and science of drilling to reach a predetermined subsurface target and deflect the borehole in a specific direction. That is, the drilling axis is purposefully changed from curved to straight or from straight to curved. At the same time, the hole bottom guide device monitors the drilling parameters in real time, and then determines the oblique direction of the hole bottom screw motor. The key part of the technology lies in the motor drive device in the hole and the matching measurement technology. First, the high-pressure water is delivered to the motor in the hole through the drill pipe, and the rotor inside the motor in the hole is washed by the high-pressure water.

2021-03-23

23

2021-03

Working Conditions of Directional Drill Rod and Directional Drill Bit-Yikuang Science and Technology

Directional drill pipe working conditions Directional drill pipe composed of the drill pipe is an elastic system, in the process of directional drilling drill pipe load size and direction are changing, directional drill pipe in the three-dimensional space bear complex alternating tension, compression, torsion, bending, vibration and other loads, coupled with wear and corrosion, after a period of aging is likely to fracture in the stress concentration position. At the same time, with the change of geological conditions and the occurrence of accidents such as sticking and burying, the force of the directional drill pipe will become more complex. The working conditions of the directional drill pipe determine that the directional drill pipe will be a component with complex force and harsh working conditions in the drilling process. directional drill pipe

2021-03-23

17

2021-03

Causes and Solutions of Drill Pipe Fracture in Directional Drilling-Yikuang Technology

In order to save investment, the directional drilling equipment used by the construction contractor does not match the actual needs of the project construction, the tonnage of the directional drilling equipment is too small, the maintenance is not timely, and the failure rate is high, which makes the directional drilling force uneven. At the same time, the stop-and-go construction makes the hole quality poor, the hole is irregular, and the drilling tool is easy to lock, resulting in drill pipe fracture. 2, the drilling torque increases, the wear of the drill pipe increases and the drill pipe breaks; 3. The drill pipe selection is unreasonable, due to the lack of tracking management of the drill pipe and the lack of statistics of the test data of the drill pipe, resulting in the use of a set of drill pipe.

2021-03-17

17

2021-03

Maintenance of down-the-hole impactor and drill bit-beneficial mining technology.

The advantages of 1. down-the-hole impactor and drill bit in water well construction 1. High drilling efficiency, long drilling tool life, down-the-hole impactor rock drilling, the medium is air, there is no problem of recovery and treatment of flushing medium, and auxiliary time is reduced. 2. The use cost is low. The down-the-hole impactor requires small shaft pressure on the drilling rig, low speed, low torque, low natural power consumption, relatively thin drill pipe diameter, easy installation and disassembly, and long service life. 3, DTH impactor drilling, the hole wall is more complete, no other media pollution, basically can maintain the original formation structure and water permeability, reduce the well cleaning time, save the cost. 4, in strict

2021-03-17

17

2021-03

Yikuang Technology analyzes the reasons for the damage of the down-the-hole drill bit for you.

Air DTH hammer drilling is mainly based on high-frequency impact crushing, which can often reach more than 10 times the drilling speed of regular drilling mode, but it is easy to produce various accidents due to the influence of factors such as operation process and complex formation. Common accidents of air down-the-hole hammer drilling mainly include hammer head fracture, alloy tooth collapse, blockage, blocking, mud ring wrapping, stuck drilling, etc. The systematic technical measures formed for the following typical accidents are highly operable and have popularization value. 1. Hammer head fracture occurs at the upper end of the hammer head spline. The common causes of hammer head fracture are:(1) poor quality of the hammer head itself, stress set

2021-03-17

17

2021-03

Maintenance and Maintenance of Water Well Drilling Rig Crawler

Maintenance and Maintenance of Water Well Drilling Rig Crawler

2021-03-17

17

2021-03

The Characteristics and Scope of Application of Horizontal Directional Drilling Rig -- Yikuang Science and Technology

1. features 1. The construction process is simple, operable and easy to organize and implement. Through site investigation, design the crossing line, connect the drill bit and pipeline, and the drilling rig is in place, then construction can begin. 2. It does not pollute the environment, does not affect traffic, has little damage to the ground, and can meet the requirements of high environmental protection for urban underground pipe network construction. 3, low cost, significant social and economic benefits, can reduce the administrative examination and approval of excavation, convenient construction organization, low comprehensive cost. 4, good safety, due to the use of pipe construction, construction personnel operations are carried out on the ground, to avoid the impact of deep foundation pit operations and other adverse construction conditions, improve the safety system.

2021-03-17

< 1...505152...129 >

Copyright©2024 Shandong Yikuang Drilling Technology Co., Ltd.

Business License

Powered by:300.cn | SEO Tags